A4 marine grade stainless steel M6 bleed nipple for Brembo F05 and twin bleed P2 F08 & F09 calipers. Manufactured specially for Gutsibits as a replica of the original Brembo M6 bleed nipple

Use M10 bleed screw SSA36794 for single bleed (later) P8 calipers. Ducati ref. 079539787

See BRA36794 for rubber cap

 More than 5 in stock

Also fits Benelli 250 TS, Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 F1/Laguna Sec, KTM 250XC, KTM 250SX, KTM 250EXC,

Stainless steel M10 bleed nipple for Brembo single bleed P2 F08 (P8) calipers on pre 1998 models. This is the same length as the genuine Brembo part BRA17659. M10 bleed screw used only on rear of 2003 on models

Part of Guzzi ref. 17659260. Some brake calipers may require a longer bleed screw, we reecommend measuring your existing screw - it should be 15mm from under the flats to the base of the tip.

 5 in stock

Kit containing 2 stainless steel M10 banjo bolts for Brembo brake fittings with copper washers

Supplied with 4 crush washers. Also known as Guzzi ref. 95990033

 2 in stock

95990028-z 95990028 GU95990028 95 99 00 28
 9599 0028 9599.0028 95.99.00.28

Also fits Laverda Jota

49cm length of black pipe with clips for connecting rear master cylinder to brake fluid reservoir

Brake fluid, oil and fuel resistant. We recommend measuring your existing pipe first to check ensure this 49cm pipe will be long enough. This is not long enough for the rear brake master cylinder on V50 II and V35 I

 More than 5 in stock

Black cast aluminium cap and plastic seal for PS 15 Brembo master cylinder reservoir, this type does not have a level switch. Can be fitted to front or rear PS15 master cylinder reservoirs

This design was originally fitted to 850T, V7 Sport, 750S and S3 but will all fit all listed models. Also known as Guzzi ref. 17661150. This cap does not contain a fluid level switch (your original cap may). Brembo ref. 110430820

 Sorry, this part is no longer available.

 14661100 GU14661100 14 66 11 00
 1466 1100 1466.1100 14.66.11.00

Cover rubber for PS 13 and PS 16 brake master cylinder lever

Brembo ref. 110353040

 This part is available by special order, request a quote

 27663615 GU27663615 27 66 36 15
 2766 3615 2766.3615 27.66.36.15

99cm length of black pipe with clips for connecting rear master cylinder to brake fluid reservoir

Brake fluid, oil and fuel resistant. This is long enough for the rear brake master cylinder on V50 II and V35 I

 More than 5 in stock

Kit consisting of black plastic cap and rubber cap seal for PS 12 round handlebar master cylinders and single horizontal outlet remote reservoirs (e.g. BRG19901 )

Also known as Guzzi ref. 17661052, 10271110. Brembo ref. 110430830. This is the smaller of the two round master cylinder caps used on V35, V50, V65 and 850/1000 models

 4 in stock

 10430830 GU10430830 10 43 08 30
 1043 0830 1043.0830 10.43.08.30

Also fits Ducati 500 SL Pantah, Ducati 350/500 Twin GTV, Ducati 350/500 SL Pantah, Benelli 500 Quattro, Benelli 504 Sport, Benelli 250 2C, Benelli 900 Sei

Brake pad spring for single pin Brembo Goldline 30/34 calipers

Also suitable for some Ducati / Aprilia models. Brembo ref. 98.8248.50

 1 in stock

 20419685 GU20419685 20 41 96 85
 2041 9685 2041.9685 20.41.96.85

Brakelight switch for handlebar mounted master cylinder

Stop light switch also known as Guzzi ref. 30530526. Please compare with your existing switch to check compatibility. Can be used as a substitute for ELA27815 or ELA30860. Sometimes supplied with three terminals, in this instance disregard middle terminal. Please note that terminals are smaller than standard switch and will need to be soldered on.

 1 in stock

 30749860 GU30749860 30 74 98 60
 3074 9860 3074.9860 30.74.98.60